Page 1 of 1

INSTALLAZIONE DRIVER RAID AMD

Posted: 6 June 2018, 14:19
by Alex-G
BOARD ASRock AB350M-HDV + AMD A6

LA System Board supporta un tipo di Raid ibrido HW-SW che richiede degli specifici driver, qua sotto riportati
https://support.amd.com/en-us/download/ ... nux+x86_64

L' intento sarebbe di istallare ROSA FRESH R10 su un array di questo tipo, le istruzioni allegate nel file (vedere allegato) riguardano solo le distro RHEL e UBUNTU che hanno 2 metodi diversi: in teoria dovrebbe essere parimenti possibile anche con Rosa, mi chiedevo quale fosse quello da eventualmente poter usare. Grazie in anticipo per qualsiasi suggerimento.

Re: INSTALLAZIONE DRIVER RAID AMD

Posted: 8 June 2018, 12:37
by andreas
Non ho letto il documento, ma non avrei tanti dubbi: RHEL (Red Hat Enterprise Linux), visto che Rosa è una sua tris-nipote ed utilizza gli rpm e non i deb.

Re: INSTALLAZIONE DRIVER RAID AMD

Posted: 9 June 2018, 14:05
by Alex-G
Probabilmente si ma non darei tutto troppo per scontato perché leggendo la procedura ci sono dei dettagli che differiscono dalle distro derivate da mandriva, per cui ci sono dei passaggi dei quali, così di primo acchito, non saprei trovare degli equivalenti omologhi in Rosa oppure Openmandriva, chiaramente ora vado a braccio, dovrei cimentarmi e verificare direttamente, cosa che inizierò a fare a breve.

Di seguito la copia del testo che riguarda la procedura versione UEFI

Code: Select all

Install the AMD-RAID UEFI drivers during a RHEL 7.x Linux Installation
NOTE: Prior to starting this procedure, obtain the AMD-RAID drivers from your system supplier or
motherboard vendor. Copy the AMD-RAID drivers to a USB flash drive. See Copy AMD-RAID drivers: Linux.
NOTE: When installing Red Hat Linux, use the Linux dd installation mode instead of the Linux expert mode.
NOTE: Not all of the windows indicated in this procedure will appear during the installation.
    1. Power-on the system.
    2. Insert the Red Hat operating system CD-ROM or DVD into the system’s CD or DVD drive.
    3. Create a bootable array, see Section 3.
    4. At the Red Hat Enterprise Linux Welcome window
            • Press the Up Arrow
            • Select Install Red Hat Enterprise Linux 7.x (should be listed White)
            • Press the E key
            • Press the down arrow to the linuxefi /images entry
            • Press the END key
            • Add “modprobe.blacklist=ahci inst.dd nomodeset” to the end of the string
                       Example – linuxefi /images……..quiet modprobe.blacklist=ahci inst.dd nomodeset
            • Press CTRL X
    5. Wait for the Driver Disk Device Selection to appear
               Insert the USB drive (which contains the AMD-RAID drivers) into the USB port.
            • Press the r key
            • Press Enter
    6. At the Driver Disk Device Selection
            • Press 1 – number of the flash drive
            • Press Enter
    7. At the Choose Driver Disk ISO file
            • Press 1 – number of the dd-rcraid-RHEL….el7.x86_64.iso entry
            • Press Enter
    8. At the Select Drivers to Install
            • Press 1 – number of the /media/DD/…..x86_64.rpm entry
            • Press Enter
               The /media/DD/… is now selected and should look like [X] /media/DD/……x86_64.rpm
            • Press C
            • Press Enter
10. At the Welcome to Red Hat Enterprise Linux Screen
        • Choose the desired Language
        • Choose the desired Country
        • In the bottom right corner, Click Continue

-------------

11. At the Installation Summary Screen
        • Configure the following:
        • Under Localization
        •     Date and Time
        •     Keyboard
        •     Language Support
        • Under Software
        •     Installation Source
        •     Software Selection
        •             Under Base Environments
        •                     Select Server with GUI
        •             Under Add-Ons for Selected Environments
        •                     Select Compatibility Library
        •     In the upper left corner, Click Done
        • Under System
        •     Installation Destination
        •             Under Local Standard Disks
        •                     Select AMD-RAID Array
        •             In the upper left corner, Click Done
        •     Configure Kdump
        •     Network and Hostname
        •     In the bottom left corner, enter a valid Hostname
        •             Select a Ethernet Port
        •             In the bottom right corner, Click Configure
        •             Enter valid entries
        •             Click Save
        •     In the upper left corner, Click Done
12. In the bottom right corner, Click Begin Installation
13. At the Configuration Window
        • Click Root Password
        •     Enter an applicable root password
        •     Re-enter the root password
        • In the upper right corner, Click Done
12. In the bottom right corner, Click Begin Installation
13. At the Configuration Window
        • Click Root Password
        •     Enter an applicable root password
        •     Re-enter the root password
        • In the upper right corner, Click Done
        • Click User Creation
        •     Enter a Full Name
        •     Enter a Username
        •     Enter an applicable password
        •     Re-enter the user password
        • In the upper right corner, Click Done
14. At the Installation Complete
        • In the bottom right corner, Click Reboot
        • Remove the USB flash drive
        • Once the installation media has been ejected, remove it
15. At the Initial Setup Window
        • Click License Information
        • Review and Select (Check Mark) I accept the License Agreement
        • If desired, Configure Subscription Management Registration
        • If not already configured, configure Configure Network & Hostname
        • In the upper left corner, Click Done
        • In the bottom right corner, Click Finish Configuration

16. If a pop-up appears stating that the system has to reboot
         • Click OK
17. Login to the system
         • Select a user
         • Enter a password
18. At the Welcome window
         • Select the desired Language
         • Click Next
19. At the Typing – Select your Keyboard Layout or Input Sources Window
         • Select the desired Input Source
         • Click Next
20. If desired, Configure Online Accounts
         • Click Next
21. Click Start using Red Hat Enterprise Linux Server
22. For RHEL 7.x x64 installs, manually load the following el7.686 rpms.
         • Allow the system to boot and login as root when prompted.
         • Insert the RHEL 7.x 64 installation CD/DVD into the system.
         • Install the following rpms:
         xiv.   libX11…el7.i686
          xv.   libXau…el7.i686
         xvi.   libxcb…el7.i686
        xvii.   libXext…el7.i686
       xviii.   libXi…el7.i686
       xix.     libXtst…el7.i686
        xx.     gtk2……el7.i686
         xxi.   libstdc++*.el7.i686
        xxii.   libSM-*.el7.i686
       xxiii.   libpng12*.el7.i686
       xxiv.    adwaita-gtk2-theme-*.el7.i686
        xxv.    libcanberra-gtk2-*.el7.i686
       xxvi.    PackageKit-gtk3-module-*.el7.i686
23. Open a Web Browser
      v.   Go to rpmfind.net
     vi.   Search for compat-libstdc++-33
    vii.   Download and install the compat-libstdc++-33-3.2.3-71.el7.i686.rpm
    viii.  Reboot system.

Re: INSTALLAZIONE DRIVER RAID AMD

Posted: 10 June 2018, 19:49
by andreas
Mai provato ad installare dei drivers durante l'installazione, ma tutto fa pensare che tu debba ricorrere all'installazione da riga di comando e non a quella classica tramite gui.
È possibile che l'installazione vecchia maniera ti permetta di accedere al menù richiesto. Non resta che provare....

Re: INSTALLAZIONE DRIVER RAID AMD

Posted: 22 June 2018, 13:16
by Alex-G
DUUUNQUE

Nothing to do

ho provato a seguire le istruzioni per RHEL ma non fungono

Code: Select all

1. Power-on the system.
    2. Insert the Red Hat operating system CD-ROM or DVD into the system’s CD or DVD drive.
    3. Create a bootable array, see Section 3.
    4. At the Red Hat Enterprise Linux Welcome window
            • Press the Up Arrow
            • Select Install Red Hat Enterprise Linux 7.x (should be listed White)
            • Press the E key
            • Press the down arrow to the linuxefi /images entry
            • Press the END key
            • Add “modprobe.blacklist=ahci inst.dd nomodeset” to the end of the string
                       Example – linuxefi /images……..quiet modprobe.blacklist=ahci inst.dd nomodeset
            • Press CTRL X
    *==> 5. Wait for the Driver Disk Device Selection to appear
La procedura è già fallita al punto 5, sia premendo CTRL+X sia conil semplice invio, nulla .

A questo punto installo il sistema in modo classico tenendo l' altro disco per backup

Domanda: c'è modo di installare dei driver RAID aggiuntivi nella versione LIVE di Rosa, escludendo i driver AHCI senza riavviare? perché in questo modo potrei risolvere semplicemente facendo vedere a RosaLive il disco Raid x poi trasferire sul disco RAID la sua immagine